Sampson Moisture Cure Urethane
Tough Finish That’s Great for High Traffic Areas
Sampson Moisture Cure Urethane is a urethane finish that offers toughness and flexibility, with resistance to grease, water and chemicals. Perfect for high traffic areas, the formula offers outstanding resistance to abrasion and wear and can be used on all types of wood floors.
BRAND
APPLICATION
BASE
- Offers outstanding resistance to abrasion and wear
- Tough and flexible finish, with resistance to grease, water and chemicals
- Perfect finish for high traffic areas
- Available In 350 VOC Formulation
- Available In Super High Gloss, Satin And Semi Gloss Finishes, In 1 Gallon And 5 Gallon Sizes
| Item Number | Size | Sheen | VOC | Coverage Rate | Dry Time |
|---|---|---|---|---|---|
| GRMCG1 | 1 Gal | Super High Gloss | 350 | 600 sq ft/gal | 6-8 Hrs |
| GRMCG5 | 5 Gal | Super High Gloss | 350 | 600 sq ft/gal | 6-8 Hrs |
| GRMCSG1 | 1 Gal | Semi Gloss | 350 | 600 sq ft/gal | 6-8 Hrs |
| GRMCSG5 | 5 Gal | Semi Gloss | 350 | 600 sq ft/gal | 6-8 Hrs |
| GRMCS1 | 1 Gal | Satin | 350 | 600 sq ft/gal | 6-8 Hrs |
| GRMCS5 | 5 Gal | Satin | 350 | 600 sq ft/gal | 6-8 Hrs |
Sampson Moisture Cure Urethane 350 VOC – Super High Gloss
Sampson Moisture Cure Urethane 350 VOC – Semi Gloss
Sampson Moisture Cure Urethane 350 VOC – Satin
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
DANGER. Contains isocyanate resin and Aromatic solvents. May be fatal if swallowed or inhaled. Causes serious eye irritation. Harmful if absorbed through skin. Prolonged or frequently repeated skin contact may cause sensitization to the diisocyanate or polyisocyanates in some individual. Do not breathe vapors, spray mist, dust or chips from sanding. Avoid contact with skin, eyes or clothing. While spraying paint, or sanding surface, wear a mask or respirator approved by the National Institute for Occupational Safety and Health for product that contains isocyanates. Wear protective clothing (long sleeved cotton shirt, long pants, hat, gloves (such as nitril or butyl). Shoes and socks. Wash thoroughly with soap and water after handling and before eating, drinking, using tobacco or using the toilet. Remove contaminated clothing and wash before reuse. Use adequate ventilation. Reports have associated repeated and prolonged exposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.
Follow manufacturer’s instructions for cleaning/maintaining Personal Protection Equipment (PPE). If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
FIRST AID
IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. Call a poison control center or doctor for treatment advice.
IF SWALLOWED: Call a poison control center or doctor immediately for treatment advice. Have a person sip a glass of water if able to swallow. Do not induce vomiting unless told to do so by a poison control center or doctor. Never give anything by mouth to an unconscious person.
IF ON SKIN OR CLOTHING: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment.
IF INHALED: Move person to fresh air. If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably mouth to mouth, if possible. Call a poison control center or doctor immediately for further treatment advice. For additional information in case of emergency call toll free Chemtrec – 1-800-424-9300. Have the product container or label with you when calling a poison control center or doctor or going for treatment.
PHYSICAL AND CHEMICAL HAZARDS (STORAGE)
Do not use or store near heat, sparks or open flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone.
Spill: Absorb with inert and dispose of as specified under “Clean Up”.
Clean Up: Xylene or Lacquer thinner. To avoid spontaneous combustion, soak soiled rags and waste immediately after use in water-filled, closed metal container.
IMPORTANT STORAGE AND DISPOSAL-DANGER! Rags, steel wool or waste soaked with the product may spontaneously catch fire if improperly discarded. Immediately after use place the rags, steel wool or waste in sealed water-filled metal container. Do not store unused product inside the home. Store in well-ventilated place, keep container tightly closed.
Disposal: This product contains organic solvents which may cause adverse effects to the environment if handled improperly. Empty containers may retain residue. Follow label warnings even after the container is emptied. Residual vapor may explode on ignition. For disposal guidance, contact your sanitation department or State-designated environmental agency.
Refer to Safety Date Sheet for additional health and safety information.
KEEP OUT OF THE REACH OF CHILDREN
SURFACE PREPARATION AND APPLICATION
WOOD FLOORS – NEW: Surfaces must be clean, smooth and dry. Remove wax, grease, etc. Avoid using fillers that contain stearates. Sand surfaces finishing with fine sandpaper in the direction of the grain. Remove dust by vacuuming and then tack mop using clean, lint free rags moistened with mineral spirits or naphtha.
WOOD FLOORS – OLD: Remove old finishes completely. Sand and prepare surfaces same as new work.
CONCRETE AND EPOXY FLOORS: Request appropriate literature and directions on cleaning, preparation and application from CLASSIC WORLD Coatings. Apply only to properly cleaned and prepared surfaces.
HANDLING: Loosen closure carefully, container may be under slight pressure. Withdraw only enough from original container for use in one day. After withdrawal, keep container closed to prevent contact with moisture vapor which may cause gellation. Material withdrawn from original container should be stored separately and used promptly.
APPLICATION – WOOD FLOORS: See side panels for thinning instructions and important notes on use of Satin Finishes. Seal sanded surfaces with one coat of CLASSIC WORLD Moisture Curing Polyurethane. Apply by brush or lamb’s wool applicator at room temperature and not in direct sunlight. Apply cross grain and finish with grain in long even strokes. Avoid excessive brushing. Allow finish to dry 12 to 18 hours and then screen sand with 80 grit screening discs. Proper sanding is evidenced by a matte finish, and generation of a light powder on the surface. Vacuum and tack mop before re-coating using a lint free cloth moistened with mineral spirits or fast dry naphtha. Apply one or two more coats of finish making sure to screen, vacuum and tack mop between coats. Floors are ready for use after 24 hours curing of final coat. Cure time will vary depending on temperature and humidity. NOTE: Where sanding between coats is impractical, recoat within 12 hours.
STAINING: Apply stains according to manufacturer’s instructions on can. Allow stain to dry at least 24 hours before re-coating with CLASSIC WORLD Moisture Cure Finishes. In hot or humid weather, stain may require an additional 24 to 72 hours dry time.
COVERAGE: 300 to 600 square feet per gallon depending upon surface.
DRYING & CURING: Best results are obtained when temperature is between 65°F and 95°F and relative humidity between 50% and 70%. If Gloss or Satin Moisture Cure takes too long to set and dry, add 1 to 3 oz. of Moisture Cure Catalyst per gallon to speed up dry time. In extremely hot and humid weather, Moisture Cure may set up too quickly. The addition of 4 to 8 oz. per gallon of Moisture Cure Retarder will slow set time and improve flow and leveling.
OPENING FLOORS TO TRAFFIC: To avoid premature scuffing and marring, before opening floors to heavy traffic, allow a minimum of 48 to 72 hours additional cure time after application of final coat of finish.
CLEAN-UP: All equipment should be cleaned immediately after use with CLASSIC WORLD Moisture Cure Reducer or xylol.
WARNING: Floors finished with polyurethane may become slippery when wet.
IMPORTANT NOTE ON USE OF MOISTURE CURE SATIN FINISHES
FOR MAXIMUM DURABILITY AND INTER-COAT ADHESION – Apply CLASSIC WORLD Satin Finish Moisture Curing Polyurethanes as a last coat only, over 1 or 2 coats of gloss finish. Failure to follow this method may result in improper wear and scratching. NOTE: Do not mix Moisture Cure Gloss and Moisture Cure Satin to achieve higher or lower gloss. Improper mixing may lead to variations in gloss causing uneven dull or shiny spots on floor. Do not mix Standard Aromatic and Non-Yellowing Aliphatic materials. Be sure to stir Satin Finish well before and during use.
DIRECTIONS FOR THINNING
IN VOC REGULATED AREAS DO NOT ADD THINNER TO THIS PRODUCT
In all other areas, thin first coat to gloss moisture cure 5 to 15% with CLASSIC WORLD Moisture Cure Reducer. Then successive coats 5 to 10%. Do not thin Satin Finish Moisture Cure unless heat or high humidity is causing flash drying and excessive brush drag.
FOR PROFESSIONAL USE ONLY
WARRANTY: Since the use and application of this product is beyond the control of the seller or manufacturer, the sole responsibility under this guarantee and under any other warranty guarantee, expressed or implied, in connection with the sale and use of this material, shall be the return of the purchase price of this material or, at the seller’s option, replacement of the material, if proven defective. Factors beyond our control prevent us from assuming responsibility for damage to property or persons, even when this product is applied according to directions. In no event shall our liability exceed the purchase price hereof.
MAXIMUM VOC CONTENT: 350 grams/liter
