- Easy to Apply
- Reliable Drying
- Hard Cure
- VOC Compliant
New Floor
- Supreme Stain – Dry 3 hours
- Primero – Dry Overnight
- Abrade Floor/Tack with water
- Primero – Dry 72 Hours
Screen & Recoat
- Clean Floor with Tie Tack
- Abrade Floor/Vacuum/Tack with Water
- Primero – Dry 72 hours
Available In 1 Quart, 1 Gallon And 5 Gallon Containers
| VOC | <500 g/L |
| Solids | 42-46% |
| Flash Point | >101F |
| Dry Time | 12 hrs |
| Cure Time (80%) | 72 hours |
| Coverage | 500 sf/gal |
| Open Time | 15 min |
| Sward Hardness | Pencil 2H |
| Color | Amber |
NEW INSTALLATIONS OR RESANDS:
- Sand floors according to NWFA procedures. Any existing finish on floor must be removed to ensure proper adhesion. Sweep and vacuum to remove all
dust and loose particles on the floor. - If staining, wait 5 hrs before top coating. If sealing, wait overnight and abrade before top coating. If using semi-gloss, satin, or satin matte, stir contents well before use. Eliminate direct air drafts during application. Apply with roller, lambswool, brush, or T-bar @ 500 sq ft/gal.
- Increase airflow when floor is tack free (usually 4 – 5 hrs). Allow overnight dry before application of next coat and abrade between coats with 150 or 180 grit screens (3M SPPs with 180 grit disks may also be used if top coating within 36 hrs.)
- Keep traffic off floor for 24 hours. / Primero – Light traffic until 3 days. / Supreme – Light traffic until 7 days. / Normal traffic after that. Supreme reaches 80% cure in 7 days, full cure in 30 days. No rugs for 30 days. Primero reaches 80% cure in 3 days, full cure in 14 days. No rugs for 14 days.
TIPS: Ensure wood is acclimated before installation. Minimize wood movement by maintaining constant temperature and humidity in facility before, during, and after installation. This will also reduce gaps in the wood and polyball formation. Do not mix coats of Low VOC with Supreme and Primero Products.
RECOATS:
- Clean floor with Craftsman’s Choice Tie Tack prior to screening.
- Abrade with 120, 150, or 180 grit screens depending upon condition of floor.
- Sweep, vacuum, and then tack with clean water or virgin mineral spirits and allow to thoroughly dry.
- Eliminate direct air drafts during application. Apply with roller, lambswool, brush, or T-bar @ 500 sq ft/gal. Increase airflow when floor is tack free (usually 4 – 5 hrs)
- Keep traffic off floor for 24 hours. / Primero – Light traffic until 3 days / Supreme – Light traffic until 7 days. / Normal traffic after that. Supreme reaches 80% cure in 7 days, full cure in 30 days. No rugs for 30 days. Primero reaches 80% cure in 3 days, full cure in 14 days. No rugs for 14 days.
DISPOSAL: Rags, steel wool and other waste soaked with oil finishes may spontaneously catch fire if improperly discarded. Dispose of rags and waste products in a sealed metal container or in accordance with local government and fire regulations. To avoid spontaneous combustion, do not allow dust from abraded or sanded floors to accumulate in piles, trash cans, vacuum cleaners, etc. Never leave dust or shavings in any container inside a facility overnight.
GUARANTEE
We guarantee this PoloPlaz product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
DANGER
HAZARD STATEMENTS:
Flammable liquid and vapor
Causes skin irritation
May be fatal if swallowed and enters airways
Causes eye irritation
Suspected of causing cancer
PRECAUTIONARY STATEMENTS:
Keep out of reach of children
Read label before use
Do not handle until all safety precautions have been read and understood
Avoid breathing fume/dust/mist/vapors/spray
Get medical advice/attention if you feel unwell
In case of inadequate ventilation wear respiratory protection
Wear protective gloves/protective clothing/eye protection
Use only outside or in a well-ventilated area
Do not eat, drink, or smoke when using this product
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking
Use only non-sparking tools
Take precautionary measures against static discharge
Wash hands thoroughly after handling
Keep container tightly closed
Store in a well-ventilated place. Keep cool
Store locked up
Avoid release to the environment
Dispose of contents/container in accordance with local/regional/national/international regulation
FIRST AID:
IF SWALLOWED: Immediately call a POISON CENTER/doctor/911
Do not induce vomiting
IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower
IF INHALED: Remove person to fresh air and keep comfortable for breathing
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
V.O.C < 575 g/l.
- PRODUCT DESCRIPTION
- TECHNICAL SPECIFICATIONS
- SDS
- TDS
- DIRECTIONS
- Easy to Apply
- Reliable Drying
- Hard Cure
- VOC Compliant
New Floor
- Supreme Stain – Dry 3 hours
- Primero – Dry Overnight
- Abrade Floor/Tack with water
- Primero – Dry 72 Hours
Screen & Recoat
- Clean Floor with Tie Tack
- Abrade Floor/Vacuum/Tack with Water
- Primero – Dry 72 hours
Available In 1 Quart, 1 Gallon And 5 Gallon Containers
| VOC | <500 g/L |
| Solids | 42-46% |
| Flash Point | >101F |
| Dry Time | 12 hrs |
| Cure Time (80%) | 72 hours |
| Coverage | 500 sf/gal |
| Open Time | 15 min |
| Sward Hardness | Pencil 2H |
| Color | Amber |
NEW INSTALLATIONS OR RESANDS:
- Sand floors according to NWFA procedures. Any existing finish on floor must be removed to ensure proper adhesion. Sweep and vacuum to remove all
dust and loose particles on the floor. - If staining, wait 5 hrs before top coating. If sealing, wait overnight and abrade before top coating. If using semi-gloss, satin, or satin matte, stir contents well before use. Eliminate direct air drafts during application. Apply with roller, lambswool, brush, or T-bar @ 500 sq ft/gal.
- Increase airflow when floor is tack free (usually 4 – 5 hrs). Allow overnight dry before application of next coat and abrade between coats with 150 or 180 grit screens (3M SPPs with 180 grit disks may also be used if top coating within 36 hrs.)
- Keep traffic off floor for 24 hours. / Primero – Light traffic until 3 days. / Supreme – Light traffic until 7 days. / Normal traffic after that. Supreme reaches 80% cure in 7 days, full cure in 30 days. No rugs for 30 days. Primero reaches 80% cure in 3 days, full cure in 14 days. No rugs for 14 days.
TIPS: Ensure wood is acclimated before installation. Minimize wood movement by maintaining constant temperature and humidity in facility before, during, and after installation. This will also reduce gaps in the wood and polyball formation. Do not mix coats of Low VOC with Supreme and Primero Products.
RECOATS:
- Clean floor with Craftsman’s Choice Tie Tack prior to screening.
- Abrade with 120, 150, or 180 grit screens depending upon condition of floor.
- Sweep, vacuum, and then tack with clean water or virgin mineral spirits and allow to thoroughly dry.
- Eliminate direct air drafts during application. Apply with roller, lambswool, brush, or T-bar @ 500 sq ft/gal. Increase airflow when floor is tack free (usually 4 – 5 hrs)
- Keep traffic off floor for 24 hours. / Primero – Light traffic until 3 days / Supreme – Light traffic until 7 days. / Normal traffic after that. Supreme reaches 80% cure in 7 days, full cure in 30 days. No rugs for 30 days. Primero reaches 80% cure in 3 days, full cure in 14 days. No rugs for 14 days.
DISPOSAL: Rags, steel wool and other waste soaked with oil finishes may spontaneously catch fire if improperly discarded. Dispose of rags and waste products in a sealed metal container or in accordance with local government and fire regulations. To avoid spontaneous combustion, do not allow dust from abraded or sanded floors to accumulate in piles, trash cans, vacuum cleaners, etc. Never leave dust or shavings in any container inside a facility overnight.
GUARANTEE
We guarantee this PoloPlaz product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
DANGER
HAZARD STATEMENTS:
Flammable liquid and vapor
Causes skin irritation
May be fatal if swallowed and enters airways
Causes eye irritation
Suspected of causing cancer
PRECAUTIONARY STATEMENTS:
Keep out of reach of children
Read label before use
Do not handle until all safety precautions have been read and understood
Avoid breathing fume/dust/mist/vapors/spray
Get medical advice/attention if you feel unwell
In case of inadequate ventilation wear respiratory protection
Wear protective gloves/protective clothing/eye protection
Use only outside or in a well-ventilated area
Do not eat, drink, or smoke when using this product
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking
Use only non-sparking tools
Take precautionary measures against static discharge
Wash hands thoroughly after handling
Keep container tightly closed
Store in a well-ventilated place. Keep cool
Store locked up
Avoid release to the environment
Dispose of contents/container in accordance with local/regional/national/international regulation
FIRST AID:
IF SWALLOWED: Immediately call a POISON CENTER/doctor/911
Do not induce vomiting
IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower
IF INHALED: Remove person to fresh air and keep comfortable for breathing
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
V.O.C < 575 g/l.
