PoloPlaz FastTrak 2K Waterborne Finish
PoloPlaz FastTrak is a unique waterborne finish designed for recoating gym floors in just a single coat. With 50% solids, it provides a very durable playing surface and incredibly high gloss shine not typically seen in waterbornes. FastTrak is virtually odorless and has VOC content low enough to use anywhere on any job… including LEED projects. Your customer can resume use of their floor in as little as 24 hrs. Don’t compromise your schedule. Save time and labor with the one-coat FastTrak system from PoloPlaz.
BRAND
APPLICATION
BASE
Use For:
- VOC compliant coatings are required
- Schedule is tight and no time for drying delays
- Facility is occupied and won’t tolerate offensive odors
- Budget won’t allow two coats waterbase + extra labor
Application:
- Clean floor with Tie Tack or Hardwood Floor Cleaner.
- Abrade floor with 180 grit 3M™ Hookit II discs attached to 3M™ Surface Prep Pads (SPP) until completely deglossed.
- Vacuum dust and then tack floor with water-dampened towels until clean (no mineral spirits).
- Apply with a lightweight T-bar @ 400 sq.ft./gallon with no pressure to handle. FastTrak will appear white when applied, but will dry clear.
Formulation:
- Solids: 50%
- VOCs: <100 g/L
- Flash Point: N/A
- Solvent: Water, Glycol
- Shelf Life: 1 year
Tips:
- Only apply when floor temp is between 70°F and 90°F.
- Apply evenly and avoid puddling for best curing results
- The key to a successful recoat is to achieve a smooth
abraded surface on which to apply the top coat.
Available In 5 Gallon Containers
| V.O.C. | <100 g/L |
|---|---|
| Solids | 50% |
| Flash Point | N/A |
| Cure Time (100%) | 48 hours |
| Coverage | 400 sf/gal |
| Open Time (wet edge) | 10 mins |
| Solvent | Water/Glycol Ether |
DESCRIPTION:
PoloPlaz FastTrak is a high solid, low VOC (< 100 g/l), premium quality, commercial grade, 2K waterborne finish designed for professionals to recoat hardwood sports floors.
MIXING INSTRUCTIONS:
The mix ratio by volume is 1 Part B : 4 Parts A. Mix components together thoroughly. This is best achieved by removing lid from pail and pouring Part B slowly in to Part A while stirring. Mix for 2 minutes. Be sure to replace the lid so that the pour spout is perpendicular to ears on the container.
PRECAUTIONS:
Do not apply if air, product, or floor temperature is below 70°F. FastTrak will not cure properly in cold conditions. Discoloration of alkyd paints in the facility may occur if they were applied within one week of FastTrak application.
This would include game line paints and wall or structural paints. FastTrak has a 3-hour pot life at 75°F (2 hrs @ 85°F and 1 hr @ 95°F). Prevent Spontaneous combustion: Do not allow dust from screened or sanded floors to accumulate in piles, trash cans, vacuum cleaners, etc. and never leave dust in any container inside a facility overnight. Do not allow excessive amounts of FastTrak to dry on floor. Product that dries in puddles or divots may appear white when dried. Heavy application may become cloudy or yellowish when dried. Ventilate area to prevent solvent rainback. Do not apply if humidity is above 70% in facility. Do not use steel wool when using this product. Low temp, high humidity and heavy application may extend dry time. On lengthy jobs, change T-bar applicator after 1 1/2 hours to prevent finish from setting up on applicator. Do not place rugs on floor for one week. Store at room temperature. Avoid freezing. If frozen, slowly return to room temperature without stirring, then stir once product has completely liquefied. Discard waste according to local government regulations. Not for exterior application.
APPLICATION INSTRUCTIONS:
Thoroughly clean floor with Tie Tack or Hardwood Floor Cleaner. Abrade floor with 180 grit 3M™ Hookit™ II discs attached to 3M™ Surface Prep Pads (SPP) until completely deglossed. The key to a successful recoat is to achieve a smooth surface on which to apply the topcoat. If the original floor is rough or has imperfections (badly scratched, divots, chipping and peeling, swirl marks etc.) a clear coat is never going to cover such imperfections. To achieve the smooth surface, it may be necessary to abrade more aggressively first, then abrade again using the 180 grit 3M Hookit™ II discs on 3M™ SPPs. Vacuum dust and then tack floor with water-dampened towels until clean (no mineral spirits). Eliminate direct air drafts during application of FastTrak. Apply with a lightweight T-bar @ 400 sq.ft./gallon with no pressure to handle. FastTrak will appear white when applied but will dry clear. Do not leave puddles to dry on floor as they will not cure properly and could remain white. Resume air flow upon exiting the facility. Floor may be returned to service 24 hours after coating has completely dried (min. temp of 75°F & 50% RH or less, and adequate air exchange is maintained during curing).
TOOLS FOR THE JOB:
3M™ 180 Grit Hookit™ II Sanding Discs
3M™ SPP Pads
Stirring Paddles for 5 Gallon Buckets
Plenty of Clean Tacking Towels, Rags
24 Inch Push Brooms for Tacking
Extra 5 Gallon Buckets
Laser Thermometer for floor, air, and product
Hygrometer
GUARANTEE
We guarantee this PoloPlaz product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
WARNING: This product can expose you to chemicals including Bisphenol A, which is known to the state of California to cause reproductive harm. For more information go to: www.P65Warnings.ca.gov
WARNING
HAZARD STATEMENTS:
May cause an allergic skin reaction
May cause drowsiness or dizziness
Harmful if swallowed
Causes serious eye irritation
PRECAUTIONARY STATEMENTS:
Keep out of reach of children
Read label before use
Obtain special instructions before use
Avoid breathing fume/dust/mist/vapors/spray
If exposed or concerned: Get medical advice/attention
Wear protective gloves/protective clothing/eye protection
Use only outside or in a well-ventilated area
Do not eat, drink, or smoke when using this product
Wash hands thoroughly after handling
Store in a well-ventilated place
Store locked up
Keep container tightly closed
Dispose of contents/container in accordance with local/regional/national/international regulation
Do not handle until all safety precautions have been read and understood
FIRST AID:
IF ON SKIN: Wash with plenty of soap and water
IF SKIN IRRITATION PERSISTS: Get medical advice/attention
Take off contaminated clothing and wash before reuse
IF INHALED: Remove person to fresh air and keep comfortable for breathing
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
If eye irritation persists: Get medical advice/attention
Call a poison center/doctor/if you feel unwell
V.O.C < 100 g/l.
- PRODUCT DESCRIPTION
- TECHNICAL SPECIFICATIONS
- SDS
- TDS
- DIRECTIONS
Use For:
- VOC compliant coatings are required
- Schedule is tight and no time for drying delays
- Facility is occupied and won’t tolerate offensive odors
- Budget won’t allow two coats waterbase + extra labor
Application:
- Clean floor with Tie Tack or Hardwood Floor Cleaner.
- Abrade floor with 180 grit 3M™ Hookit II discs attached to 3M™ Surface Prep Pads (SPP) until completely deglossed.
- Vacuum dust and then tack floor with water-dampened towels until clean (no mineral spirits).
- Apply with a lightweight T-bar @ 400 sq.ft./gallon with no pressure to handle. FastTrak will appear white when applied, but will dry clear.
Formulation:
- Solids: 50%
- VOCs: <100 g/L
- Flash Point: N/A
- Solvent: Water, Glycol
- Shelf Life: 1 year
Tips:
- Only apply when floor temp is between 70°F and 90°F.
- Apply evenly and avoid puddling for best curing results
- The key to a successful recoat is to achieve a smooth
abraded surface on which to apply the top coat.
Available In 5 Gallon Containers
| V.O.C. | <100 g/L |
|---|---|
| Solids | 50% |
| Flash Point | N/A |
| Cure Time (100%) | 48 hours |
| Coverage | 400 sf/gal |
| Open Time (wet edge) | 10 mins |
| Solvent | Water/Glycol Ether |
DESCRIPTION:
PoloPlaz FastTrak is a high solid, low VOC (< 100 g/l), premium quality, commercial grade, 2K waterborne finish designed for professionals to recoat hardwood sports floors.
MIXING INSTRUCTIONS:
The mix ratio by volume is 1 Part B : 4 Parts A. Mix components together thoroughly. This is best achieved by removing lid from pail and pouring Part B slowly in to Part A while stirring. Mix for 2 minutes. Be sure to replace the lid so that the pour spout is perpendicular to ears on the container.
PRECAUTIONS:
Do not apply if air, product, or floor temperature is below 70°F. FastTrak will not cure properly in cold conditions. Discoloration of alkyd paints in the facility may occur if they were applied within one week of FastTrak application.
This would include game line paints and wall or structural paints. FastTrak has a 3-hour pot life at 75°F (2 hrs @ 85°F and 1 hr @ 95°F). Prevent Spontaneous combustion: Do not allow dust from screened or sanded floors to accumulate in piles, trash cans, vacuum cleaners, etc. and never leave dust in any container inside a facility overnight. Do not allow excessive amounts of FastTrak to dry on floor. Product that dries in puddles or divots may appear white when dried. Heavy application may become cloudy or yellowish when dried. Ventilate area to prevent solvent rainback. Do not apply if humidity is above 70% in facility. Do not use steel wool when using this product. Low temp, high humidity and heavy application may extend dry time. On lengthy jobs, change T-bar applicator after 1 1/2 hours to prevent finish from setting up on applicator. Do not place rugs on floor for one week. Store at room temperature. Avoid freezing. If frozen, slowly return to room temperature without stirring, then stir once product has completely liquefied. Discard waste according to local government regulations. Not for exterior application.
APPLICATION INSTRUCTIONS:
Thoroughly clean floor with Tie Tack or Hardwood Floor Cleaner. Abrade floor with 180 grit 3M™ Hookit™ II discs attached to 3M™ Surface Prep Pads (SPP) until completely deglossed. The key to a successful recoat is to achieve a smooth surface on which to apply the topcoat. If the original floor is rough or has imperfections (badly scratched, divots, chipping and peeling, swirl marks etc.) a clear coat is never going to cover such imperfections. To achieve the smooth surface, it may be necessary to abrade more aggressively first, then abrade again using the 180 grit 3M Hookit™ II discs on 3M™ SPPs. Vacuum dust and then tack floor with water-dampened towels until clean (no mineral spirits). Eliminate direct air drafts during application of FastTrak. Apply with a lightweight T-bar @ 400 sq.ft./gallon with no pressure to handle. FastTrak will appear white when applied but will dry clear. Do not leave puddles to dry on floor as they will not cure properly and could remain white. Resume air flow upon exiting the facility. Floor may be returned to service 24 hours after coating has completely dried (min. temp of 75°F & 50% RH or less, and adequate air exchange is maintained during curing).
TOOLS FOR THE JOB:
3M™ 180 Grit Hookit™ II Sanding Discs
3M™ SPP Pads
Stirring Paddles for 5 Gallon Buckets
Plenty of Clean Tacking Towels, Rags
24 Inch Push Brooms for Tacking
Extra 5 Gallon Buckets
Laser Thermometer for floor, air, and product
Hygrometer
GUARANTEE
We guarantee this PoloPlaz product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
WARNING: This product can expose you to chemicals including Bisphenol A, which is known to the state of California to cause reproductive harm. For more information go to: www.P65Warnings.ca.gov
WARNING
HAZARD STATEMENTS:
May cause an allergic skin reaction
May cause drowsiness or dizziness
Harmful if swallowed
Causes serious eye irritation
PRECAUTIONARY STATEMENTS:
Keep out of reach of children
Read label before use
Obtain special instructions before use
Avoid breathing fume/dust/mist/vapors/spray
If exposed or concerned: Get medical advice/attention
Wear protective gloves/protective clothing/eye protection
Use only outside or in a well-ventilated area
Do not eat, drink, or smoke when using this product
Wash hands thoroughly after handling
Store in a well-ventilated place
Store locked up
Keep container tightly closed
Dispose of contents/container in accordance with local/regional/national/international regulation
Do not handle until all safety precautions have been read and understood
FIRST AID:
IF ON SKIN: Wash with plenty of soap and water
IF SKIN IRRITATION PERSISTS: Get medical advice/attention
Take off contaminated clothing and wash before reuse
IF INHALED: Remove person to fresh air and keep comfortable for breathing
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
If eye irritation persists: Get medical advice/attention
Call a poison center/doctor/if you feel unwell
V.O.C < 100 g/l.
