PoloPlaz Express 2K Waterborne Finish
Easy application with a longer wet edge.
Express is a commercial-grade, 2 component, clear waterborne polyurethane finish. Its proprietary formula for exceptional adhesion and resistance to abrasion exceeds MFMA standards. Express features excellent flow without streaking or bubbling, and a longer wet edge to reduce lap marks. It is virtually odorless, VOC compliant and less expensive than other waterbornes in its class.
BRAND
APPLICATION
BASE
Use For:
- Basketball courts, dance floors, gyms, stages, etc.
- High-profile courts, discriminating architects
- New installation, resand or screen/recoat
Coverage:
- 500 sf/gal
Available In 5 Gallon Containers
| VOC | 262 gr/L |
| Solids | 31% |
| % Volatile | 69% |
| Flash Point | n/a |
| Dry Time | 3-5 hours |
| Cure Time (75%) | 3 days – Full Cure 10-14 days |
| Coverage | 500 sq ft/gal |
| Open Time | 10 min |
| Sward Hardness | pencil 3H |
| Color | clear |
NEW FLOORS:
After NSB coats have been abraded and tacked, paint game lines with PoloPlaz waterbase paint. Once game lines have dried thoroughly, abrade paint with 3M SPP with 180 disks. Vacuum paint dust, then tack with water, and apply third coat of NSB over the paint. Catalyze Express according to instructions on catalyst bottle. Eliminate direct air drafts on floor during application. Apply Express with a T-bar @ 400 sf/gal. Increase airflow when film has become tack free. Wait 4 – 6 hours before next coat (under normal conditions: 65 – 80˚ F and 40 – 60% RH). High humidity and cooler temperatures may extend dry times. If more than 15 hours have elapsed between coats, the floor must be abraded before next coat. Generally, three coats of seal and one coat of Express will provide adequate protection for the floor. However, use your professional discretion to achieve desired results.
SCREEN & COATS:
Clean floor with Craftsman’s Choice Tie Tack solution prior to screening. Screen floor thoroughly with new 120 grit. Vacuum, then tack with water (no mineral spirits). Allow floor to completely dry. Catalyze Express according to instructions on catalyst bottle. Eliminate direct air drafts on floor during application. Apply Express with a T-bar @ 400 sf/gal. Increase airflow when film has become tack free. Wait 4 – 6 hours before next coat (under normal conditions: 65 – 80˚ F and 40 – 60% RH). High humidity and cooler temperatures may extend dry times. If more than 15 hours have elapsed between coats, the floor must be abraded before next coat. Generally, two coats of Express will provide adequate protection for the floor. However, use your professional discretion to achieve desired results.
MAINTENANCE and CLEANUP:
For daily cleaning, use PoloPlaz Hardwood Floor Cleaner. Follow directions that accompany the cleaner. Do not use automatic floor scrubbers on hardwood floors. This will void the warranty on the floor. Tools may be cleaned with water.
GUARANTEE
We guarantee this PoloPlaz product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
WARNING: This product can expose you to chemicals including N-Methylpyrrolidone, which is known to the state of California to cause development defects. For more information go to: www.P65Warnings.ca.gov
DANGER
HAZARD STATEMENTS:
Causes skin irritation
Causes serious eye irritation
May damage fertility or the unborn child
May cause respiratory irritation
Harmful if swallowed
May cause drowsiness or dizziness
PRECAUTIONARY STATEMENTS:
Keep out of reach of children
Read label before use
Obtain special instructions before use
Avoid breathing fume/dust/mist/vapors/spray
If exposed or concerned: Get medical advice/attention
Wear protective gloves/protective clothing/eye protection
Use only outside or in a well-ventilated area
Do not eat, drink, or smoke when using this product
Wash hands thoroughly after handling
Store in a well-ventilated place. Keep cool
Store locked up
Keep container tightly closed
Dispose of contents/container in accordance with local/regional/national/international regulation
Do not handle until all safety precautions have been read and understood
FIRST AID:
IF ON SKIN: Wash with plenty of soap and water
IF SKIN IRRITATION OCCURS: Get medical advice/attention
Take off contaminated clothing and wash before reuse
IF INHALED: Remove person to fresh air and keep comfortable for breathing
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
If eye irritation persists: Get medical advice/attention
Call a poison center/doctor/if you feel unwell
V.O.C < 275 g/l.
