Court Sense 350 Gym Finish
This premium polyurethane is created for when VOC Compliant products are a must, and waterbase is not an option. Court Sense 350 is a low viscosity product that dries hard overnight and cures quickly for maximum protection.
BRAND
APPLICATION
BASE
- Smooth, Easy Application
- VOC Compliant
- Overnight Dry Times
- Exceeds MFMA Standards
- Highly Resistant To Abrasion, Staining, Scuffing, Chipping, Spills And Perspiration
| Item Number | Size | Sheen | VOC | Coverage Rate | Dry Time |
|---|---|---|---|---|---|
| 89-5CS | 5 Gal | Gloss | 350 | 500 sq ft/gal | Overnight For Recoat |
DESCRIPTION: A deep penetrating oil that delivers a high quality protective wear coating.
PREPARATIONS: Proper surface preparation is essential to achieve a high quality finish.
NEW INSTALLATIONS OR RESANDS:
- Sand floors according to MFMA procedures. Any existing finish on floor must be removed to ensure proper adhesion. 2. Sweep and vacuum to remove all dust and loose particles on the floor. 3. Eliminate direct air drafts during application. Apply 1st coat with T-bar @ 500 sq ft/gal. Allow overnight dry before application of next coat and abrade between coats with 150 or 180 grit screens (3M SPPs with 180 grit disks may also be used if top coating within 36 hrs.). Increase airflow when floor is tack free (usually 4 – 6 hrs). 4. After game lines have been applied and abraded, apply finish using the same procedures listed above. 5. Keep traffic off floor for 48 hours. Light traffic until 7 days, normal traffic after that. Coating reaches 80% cure in 7 days, full cure in 30 days. No mats or gym covers for 30 days.
TIPS: Ensure wood is acclimated before installation. Minimize wood movement by maintaining constant temperature and humidity in facility before, during, and after installation. This will also reduce gaps in the wood, paint chipping at board edges, and polyball formation.
RECOATS:
- Clean floor with PoloPlaz Mineral Spirits, PoloPlaz Tie Tack or PoloPlaz Court Care Cleaner prior to screening. 2. Abrade with 120, 150, or 180 grit screens depending upon condition of floor. 3. Sweep, vacuum, and then tack with PoloPlaz Mineral Spirits, PoloPlaz Tie Tack or PoloPlaz Court Care Cleaner and allow to thoroughly dry. 4. Eliminate direct air drafts during application. Apply with T-bar @ 500 sq ft/gal. Increase airflow when floor is tack free (usually 4 – 5 hrs). 5. Keep traffic off floor for 48 hours. Light traffic until 7 days, normal traffic after that. Coating reaches 80% cure in 7 days, full cure in 30 days. No mats or gym covers for 30 days.
DISPOSAL: Rags, steel wool and other waste soaked with oil finishes may spontaneously catch fire if improperly discarded. Dispose of rags and waste products in a sealed metal container or in accordance with local government and fire regulations. To avoid spontaneous combustion, do not allow dust from abraded or sanded floors to accumulate in piles, trash cans, vacuum cleaners, etc. Never leave dust or shavings in any container inside a facility overnight.
GUARANTEE
We guarantee this Canlak Coatings product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
Danger
Flammable liquid and vapor. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. May cause drowsiness or dizziness. May cause genetic defects. May cause cancer. Suspected of damaging fertility or the unborn child. Causes damage to organs through prolonged or repeated exposure.
Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Obtain special instructions before use.Wear protective gloves. Wear protective clothing. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a wellventilated area. Do not breathe vapor. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Call a POISON CENTER or doctor if you feel unwell. IF exposed or concerned: Get medical advice or attention. Take off contaminated clothing and wash it before reuse. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice or attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or attention. Store locked up. Store in a well-ventilated place. Keep container tightly closed. Dispose of contents and container in accordance with all local, regional, national and international regulations.
- PRODUCT DESCRIPTION
- TECHNICAL SPECIFICATIONS
- SDS
- TDS
- DIRECTIONS
- Smooth, Easy Application
- VOC Compliant
- Overnight Dry Times
- Exceeds MFMA Standards
- Highly Resistant To Abrasion, Staining, Scuffing, Chipping, Spills And Perspiration
| Item Number | Size | Sheen | VOC | Coverage Rate | Dry Time |
|---|---|---|---|---|---|
| 89-5CS | 5 Gal | Gloss | 350 | 500 sq ft/gal | Overnight For Recoat |
DESCRIPTION: A deep penetrating oil that delivers a high quality protective wear coating.
PREPARATIONS: Proper surface preparation is essential to achieve a high quality finish.
NEW INSTALLATIONS OR RESANDS:
- Sand floors according to MFMA procedures. Any existing finish on floor must be removed to ensure proper adhesion. 2. Sweep and vacuum to remove all dust and loose particles on the floor. 3. Eliminate direct air drafts during application. Apply 1st coat with T-bar @ 500 sq ft/gal. Allow overnight dry before application of next coat and abrade between coats with 150 or 180 grit screens (3M SPPs with 180 grit disks may also be used if top coating within 36 hrs.). Increase airflow when floor is tack free (usually 4 – 6 hrs). 4. After game lines have been applied and abraded, apply finish using the same procedures listed above. 5. Keep traffic off floor for 48 hours. Light traffic until 7 days, normal traffic after that. Coating reaches 80% cure in 7 days, full cure in 30 days. No mats or gym covers for 30 days.
TIPS: Ensure wood is acclimated before installation. Minimize wood movement by maintaining constant temperature and humidity in facility before, during, and after installation. This will also reduce gaps in the wood, paint chipping at board edges, and polyball formation.
RECOATS:
- Clean floor with PoloPlaz Mineral Spirits, PoloPlaz Tie Tack or PoloPlaz Court Care Cleaner prior to screening. 2. Abrade with 120, 150, or 180 grit screens depending upon condition of floor. 3. Sweep, vacuum, and then tack with PoloPlaz Mineral Spirits, PoloPlaz Tie Tack or PoloPlaz Court Care Cleaner and allow to thoroughly dry. 4. Eliminate direct air drafts during application. Apply with T-bar @ 500 sq ft/gal. Increase airflow when floor is tack free (usually 4 – 5 hrs). 5. Keep traffic off floor for 48 hours. Light traffic until 7 days, normal traffic after that. Coating reaches 80% cure in 7 days, full cure in 30 days. No mats or gym covers for 30 days.
DISPOSAL: Rags, steel wool and other waste soaked with oil finishes may spontaneously catch fire if improperly discarded. Dispose of rags and waste products in a sealed metal container or in accordance with local government and fire regulations. To avoid spontaneous combustion, do not allow dust from abraded or sanded floors to accumulate in piles, trash cans, vacuum cleaners, etc. Never leave dust or shavings in any container inside a facility overnight.
GUARANTEE
We guarantee this Canlak Coatings product to perform as advertised when applied in accordance with industry standards. Because surface preparation, application methods, and surface conditions are beyond our control, all express and implied warranties are explicitly excluded. Responsibility for claim of any kind is limited to product replacement only.
Danger
Flammable liquid and vapor. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. May cause drowsiness or dizziness. May cause genetic defects. May cause cancer. Suspected of damaging fertility or the unborn child. Causes damage to organs through prolonged or repeated exposure.
Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Obtain special instructions before use.Wear protective gloves. Wear protective clothing. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a wellventilated area. Do not breathe vapor. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Call a POISON CENTER or doctor if you feel unwell. IF exposed or concerned: Get medical advice or attention. Take off contaminated clothing and wash it before reuse. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice or attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or attention. Store locked up. Store in a well-ventilated place. Keep container tightly closed. Dispose of contents and container in accordance with all local, regional, national and international regulations.
